Assembling the NOAH Wardrobe — Step-by-Step Assembly Guide

June 13, 2026

Assembling the NOAH wardrobe successfully requires a systematic sorting of components and strict adherence to assembly steps to guarantee stability and precise gap alignment.

The NOAH series belongs to the classic flat-pack carcass furniture category. Manufactured from melamine-faced chipboard, this model provides a solid basis for storage in the bedroom, hallway, or as a robust children's bedroom wardrobe. The standard dimensions with a height of around 180 cm and a depth of 50 cm make it a space-saving solution that still offers plenty of volume for two people. Whether as a classic wooden wardrobe in oak effect or a modern grey wardrobe variant, the basic mechanical construction across this series remains identical.

This guide leads you through the assembly process of a typical 2-door model (e.g. a 120 cm wide wardrobe), but can also be applied to wider versions of the series.

Scope of Delivery and Preparation

Before using the first screwdriver, check the delivery contents. In addition to the wooden panels (side panels, base, top panel, doors, shelves, back panel), the flat packs contain a bag of furniture fittings.

Required tools:

Cordless screwdriver with torque limiter
Bit sets: cross-head PZ (Pozidriv) for most furniture assembly screws and PH (Phillips)
Rubber mallet (alternatively: standard hammer with a piece of scrap wood as a buffer)
Spirit level
Tape measure or folding rule
Pencil

Preparation tip: Sort the fittings (screws, wooden dowels, hinges) into small bowls. This saves searching time during assembly and prevents small parts from going missing.

Step-by-Step Assembly

1. Prepare Carcass Components

Assembly starts lying flat on the floor. Use the cardboard packaging as an underlay to avoid scratches on the decorative surface. First, prepare the side panels, base, and top panel. Tap the wooden dowels into the pre-drilled end faces using the rubber mallet. Screw the connecting bolts for the cam lock fasteners into the corresponding threaded holes in the side panels. Ensure you screw them in straight until the thread is no longer visible.

2. Assemble the Carcass

Fit the base and the top panel onto the prepared side panels. The wooden dowels and bolts must slide precisely into the matching holes. Now insert the round cam lock fasteners into the large holes on the inside of the base and top panel. Turn them clockwise by around 180° using a manual screwdriver until you feel them tighten firmly. This connection pulls the panels flush together.

3. Attach the Back Panel

Turn the lying carcass over so the back faces upwards. Before fixing the back panel, ensure the carcass is square. Use the tape measure to check both diagonals of the carcass (from corner to corner). If both measurements are millimetre-identical, the wardrobe is completely square. Now nail or screw the back panel into place. Start at one corner and work along the edges. The distance between nails should be around 15 cm to 20 cm.

4. Stand the Wardrobe Upright

Two people are strictly required for this step to prevent joints from tearing out. Carefully tilt the wardrobe over its long edge into the upright position. Place the piece of furniture in its final location and align it using the spirit level. For uneven floors, small shims under the side panels will help.

5. Install Interior Fittings

The side panels feature a continuous line of drill holes in the 32 mm system (hole spacing 32 mm, drilling diameter usually 5 mm). Insert the shelf supports at the desired height and place the shelves on top. The wardrobe rail is fixed under the structural shelf or to the side panels using the included rail brackets. Additional wardrobe accessories such as pull-outs or tie racks can also be integrated into the line of holes at this stage.

6. Hang the Doors

The series uses concealed hinges, also known as cup hinges. Press the hinge cup into the 35 mm cup hole in the door and screw it down. Mount the cross-shaped mounting plate onto the side panel of the carcass. Since these are overlay doors, a full overlay hinge configuration is used here. Hang the doors by sliding the hinge arm onto the mounting plate and securing it (either via a fixing screw or, with clip-on hinges, by clicking it into place).

Wall Mounting and Anti-Tip Protection

A wardrobe with a height of 180 cm or more must be anchored to the wall. Opening the doors shifts the centre of gravity forwards, which can cause the wardrobe to tip, especially when heavily loaded. Use the supplied metal bracket. Secure it to the top of the wardrobe roof panel and mark the drill hole on the wall. Always use suitable wall plugs and screws matched to your wall structure (concrete, brick, plasterboard).

Tips and Common Pitfalls

Assembling furniture works like clockwork — raw force will inevitably damage components, whereas precision ensures clean, even gap dimensions.

Overtightened screws: Cordless screwdrivers are often set too high. Use a low torque setting, especially when driving screws into softer chipboard.
Uneven door gaps: If the doors rub or hang crooked, the cup hinge needs adjustment. The front screw on the hinge arm allows the door to tilt left or right (lateral gap). The rear screw adjusts the depth (distance to the carcass), and the mounting plate screws permit height adjustments.
Sticking drawers (if applicable): Check that the ball bearing runner is mounted completely level. Even a deviation of 1.5 mm can cause the runner to jam.

FAQ — Frequently Asked Questions Regarding Assembly

How long does it take to assemble the NOAH wardrobe? For a standard 2-door wardrobe, DIYers should allow around 1.5 to 2 hours. For wider models, such as a 200 cm wide wardrobe, the assembly time increases to around 3 hours.

Can I assemble the wardrobe on my own? Preparing the components and installing the fittings can easily be done alone. However, lifting the assembled carcass upright and hanging large doors strictly requires a second person to prevent structural damage.

Which wall plugs do I need for wall mounting? That depends on your wall. For solid concrete or brick walls, standard expansion plugs (Ø 6 mm or 8 mm) are sufficient. For stud walls (plasterboard), specialised cavity anchors must be used to support tensile loads.

For further replacement hardware, mounting plates, and fitting enhancements for your bedroom storage, explore our comprehensive selection of wardrobe fittings.